Blasphemy...I know, but reverb question...
Moderators: CurtissRobin, colossal, zaphod_phil, Daviedawg, Graydon
- Bieworm
- Verbose Moderator
- Posts: 2287
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Blasphemy...I know, but reverb question...
Could it be theoretically possible, if I add a reverbdriver hammond 1750A and a 12ax7 valve, to add reverb on a 18W classic? Single valve reverb...as geoff suggested...
Would there be enough power from the PT available to do so safely?
It has the hammond PT too...
Would there be enough power from the PT available to do so safely?
It has the hammond PT too...
0 x
"THIS should be played at high volume..preferably in a residential area"
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Blasphemy...I know, but reverb question...
hey Bieworm!
are you trying to get me killed? you know ZaphodPhil is a purist with a 2lb hammer!
are you trying to get me killed? you know ZaphodPhil is a purist with a 2lb hammer!
You do not have the required permissions to view the files attached to this post.
0 x
- Bieworm
- Verbose Moderator
- Posts: 2287
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Blasphemy...I know, but reverb question...
There is no way I would want that!!!geoff 1965 wrote: βTue 02/18/20 8:11 amhey Bieworm!
are you trying to get me killed? you know ZaphodPhil is a purist with a 2lb hammer!
18 Watt Reverb - 6V6.gif
I'll refer to you in the future as 'someone
Maybe you misunderstood, but I meant reverb with both normal and trem channel intact. Just verb on the trem channel is fine, but I'd like to keep the normal channel as is. Just wondering if my transformer can handle the extra 12ax7 for the verb. I will provide the verb with food from a fender-spec'd OT like the hammond 1750A.
0 x
"THIS should be played at high volume..preferably in a residential area"
- Bieworm
- Verbose Moderator
- Posts: 2287
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Blasphemy...I know, but reverb question...
side note: there's a lot been discussed about speaker impedance vs output impedance (match, mismatch,...)
but simple question: would one considder putting a 16 Ohm speaker on the 8 Ohm tap a kind of attenuation?
I mean, that is what an attenuator does.. adding resistance, or am I wrong?
but simple question: would one considder putting a 16 Ohm speaker on the 8 Ohm tap a kind of attenuation?
I mean, that is what an attenuator does.. adding resistance, or am I wrong?
0 x
"THIS should be played at high volume..preferably in a residential area"
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Blasphemy...I know, but reverb question...
you'll need to check the spec on your PT for the 6.3V filament supply, if it's 3 amp it will handle the extra 12ax7.
0 x
- Bieworm
- Verbose Moderator
- Posts: 2287
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Blasphemy...I know, but reverb question...
Lucky me thengeoff 1965 wrote: βTue 02/18/20 8:58 amyou'll need to check the spec on your PT for the 6.3V filament supply, if it's 3 amp it will handle the extra 12ax7.
0 x
"THIS should be played at high volume..preferably in a residential area"