Preamp tube Oscillation
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
-
- Unrated
- Posts: 3
- Joined: Sat 05/21/16 8:24 am
Preamp tube Oscillation
Hi,
I have been messing around with an amp based on the Marshall 18 watt. It has two channels 1 = EF86 and 2 = 12ax7. Nothing too radical yeah just sussing out how different values and layouts change the tonal character of the amp. I have come across an issue that has me stumped. In channel 2 the tube oscillates like crazy. I have checked the connections looking for positive feedback nothing found. The resistive values are all correct when measured. No obvious shorts. Behaves the same with different 12ax7 tubes insitu. I have attached the schematic sorry it’s a photo but a working drawing with some annotation in pencil. I currently have the capacitor connecting the pre to the splitter lifted in an effort to isolate the issue. Incidentally the EF86 side works well. Thanks for reading. Regards Luke
I have been messing around with an amp based on the Marshall 18 watt. It has two channels 1 = EF86 and 2 = 12ax7. Nothing too radical yeah just sussing out how different values and layouts change the tonal character of the amp. I have come across an issue that has me stumped. In channel 2 the tube oscillates like crazy. I have checked the connections looking for positive feedback nothing found. The resistive values are all correct when measured. No obvious shorts. Behaves the same with different 12ax7 tubes insitu. I have attached the schematic sorry it’s a photo but a working drawing with some annotation in pencil. I currently have the capacitor connecting the pre to the splitter lifted in an effort to isolate the issue. Incidentally the EF86 side works well. Thanks for reading. Regards Luke
You do not have the required permissions to view the files attached to this post.
0 x
RegardsLuke
- JMPGuitars
- Super Duper Admin
- Posts: 3965
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Preamp tube Oscillation
Hi Luke,
Quite often oscillations can be caused by lead dress. Post some photos of your build so we can take a look. I also suggest "chopsticking" the wires on the suspect channel.
Thanks,
Josh
Quite often oscillations can be caused by lead dress. Post some photos of your build so we can take a look. I also suggest "chopsticking" the wires on the suspect channel.
Thanks,
Josh
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 3
- Joined: Sat 05/21/16 8:24 am
Re: Preamp tube Oscillation
Hi Josh,
Thanks for your response. Attached are some photos. It’s a bit of a rats nest largely as a result of part swapping. The section of concern is the tube base with the orange wiring.
It should be noted this is a rebuild the first build had the same issue.
Thanks for your response. Attached are some photos. It’s a bit of a rats nest largely as a result of part swapping. The section of concern is the tube base with the orange wiring.
It should be noted this is a rebuild the first build had the same issue.
You do not have the required permissions to view the files attached to this post.
0 x
RegardsLuke
- JMPGuitars
- Super Duper Admin
- Posts: 3965
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Preamp tube Oscillation
I immediately see at least two problems.
1. The shielding on that wire should be connected to the back of the pot, not the ground bus (also make sure only one end is connected to ground). You should read the threads in my signature. Shielding gets its own connection to ground, never the ground bus.
2. What is that giant copper wire looking like an antenna connected to the tube socket?
Besides that, you really need to improve the soldering quality. Watch the videos linked in the soldering thread in my signature. I could point out a LOT of things in those photos, but hopefully watching the videos will help you see the issues for yourself.
Thanks,
Josh
1. The shielding on that wire should be connected to the back of the pot, not the ground bus (also make sure only one end is connected to ground). You should read the threads in my signature. Shielding gets its own connection to ground, never the ground bus.
2. What is that giant copper wire looking like an antenna connected to the tube socket?
Besides that, you really need to improve the soldering quality. Watch the videos linked in the soldering thread in my signature. I could point out a LOT of things in those photos, but hopefully watching the videos will help you see the issues for yourself.
Thanks,
Josh
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 3
- Joined: Sat 05/21/16 8:24 am
Re: Preamp tube Oscillation
Thanks Josh, I look through the vids. Excellent tips re shielding, I didn’t know that. Yes the soldering is average it’s just tacked together really. I haven’t even cut the component leads. This is on purpose. Like I said it’s a test frame. The copper bar is a ground it’s not connected to anything other than a wire shield and ground of course. The chassis is my test build chassis it has had a fair number of builds in it. I leave the ground busses insitu.
0 x
RegardsLuke
- JMPGuitars
- Super Duper Admin
- Posts: 3965
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Preamp tube Oscillation
That copper wire is an antenna. Grounds need to be as short as possible, read the grounding thread too. ...and I would gamble that it's likely the cause of the oscillation, or at least making it worse.Lukep wrote: ↑Tue 10/12/21 8:51 pmThanks Josh, I look through the vids. Excellent tips re shielding, I didn’t know that. Yes the soldering is average it’s just tacked together really. I haven’t even cut the component leads. This is on purpose. Like I said it’s a test frame. The copper bar is a ground it’s not connected to anything other than a wire shield and ground of course. The chassis is my test build chassis it has had a fair number of builds in it. I leave the ground busses insitu.
Everything matters in amp building. The lack of proper solder = issues. The unclipped ends = issues. Long copper wires that should be short = issues.
Thanks,
Josh
2 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- Bieworm
- Verbose Moderator
- Posts: 2302
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Preamp tube Oscillation
You're right about the shielding from the shielded wire not to be attached at the ground buss. Yesterday I looked for 2 hours where an oscillation came from. On my 6G3 build there was this oscillation coming straight out of nowhere... in the end it appeared to be a shielding I attached to the ground buss. When I removed that one the oscillation stopped instantly.JMPGuitars wrote: ↑Tue 10/12/21 8:00 pmI immediately see at least two problems.
1. The shielding on that wire should be connected to the back of the pot, not the ground bus (also make sure only one end is connected to ground). You should read the threads in my signature. Shielding gets its own connection to ground, never the ground bus.
Now there is another problem... I first desoldered that shielding and noticed the noise stopping. I couldn't attach it to the back of the pot, so I cut off the shielding branch. It's a shielded wire coming from the wiper of the bright vol pot btw... that explains the loud oscillation. But now when I dime the vol pot I get oscillation again.. right at the end of the pot's travel, the last milimeter...
I will make a new shielded wire there, attaching the shield at the back of the pot.
You do not have the required permissions to view the files attached to this post.
1 x
"THIS should be played at high volume..preferably in a residential area"
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Preamp tube Oscillation
I don't agree with soldering shielding onto the back of pots, as that's a surefire way of creating ground loops through the chassis.
I am a firm believer in grounding the shield ( at one end only) to the nearest common ground point for that stage (usually at the bottom of the nearest cathode cap). That keeps all the ground currents tightly confined where they belong.
I am a firm believer in grounding the shield ( at one end only) to the nearest common ground point for that stage (usually at the bottom of the nearest cathode cap). That keeps all the ground currents tightly confined where they belong.
1 x
Nature abhors a clean tube amp
- JMPGuitars
- Super Duper Admin
- Posts: 3965
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Preamp tube Oscillation
Why would it cause a ground loop? As you said, the shielding is only connected on one end...zaphod_phil wrote: ↑Fri 10/15/21 3:34 pmI don't agree with soldering shielding onto the back of pots, as that's a surefire way of creating ground loops through the chassis.
I am a firm believer in grounding the shield ( at one end only) to the nearest common ground point for that stage (usually at the bottom of the nearest cathode cap). That keeps all the ground currents tightly confined where they belong.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Preamp tube Oscillation
The back of the pot isn't a clean ground. It's connected to the chassis, which is connected to the third wire house wiring (ugh). The best reference for the shield is at the amplifier stage itself. Connecting to the pot might not create a ground loop in the usual sense, but avoiding it and using the technique described by zaphod_phil is sound.JMPGuitars wrote: ↑Fri 10/15/21 5:10 pmWhy would it cause a ground loop? As you said, the shielding is only connected on one end...zaphod_phil wrote: ↑Fri 10/15/21 3:34 pmI don't agree with soldering shielding onto the back of pots, as that's a surefire way of creating ground loops through the chassis.
I am a firm believer in grounding the shield ( at one end only) to the nearest common ground point for that stage (usually at the bottom of the nearest cathode cap). That keeps all the ground currents tightly confined where they belong.
Jack
1 x