how hot should a tube get?

Tube-specific discussions

Moderators: colossal, zaphod_phil, CurtissRobin

Post Reply
User avatar
nutxo
Newbie
Newbie
Posts: 49
Joined: Tue 08/01/06 2:00 am
Location: Unknown

how hot should a tube get?

Post by nutxo »

how hot should a tube get? I mean like scalding hot or just warm to the touch?
0 x

User avatar
dancindave
Newbie
Newbie
Posts: 94
Joined: Tue 07/04/06 2:00 am
Location: Albuquerque,NM

Post by dancindave »

preamp is almost touchable, power tubes are hot as f@ck!!
0 x

User avatar
nutxo
Newbie
Newbie
Posts: 49
Joined: Tue 08/01/06 2:00 am
Location: Unknown

Post by nutxo »

thnaks for the quick reply :-)
0 x

novemberrain
Verbose poster
Verbose poster
Posts: 1191
Joined: Sat 01/22/05 2:00 am

Post by novemberrain »

If the glass shell melts the tube is too hot.

If your fingerprints singe on to the side of the tube it's too hot.

Seriously, if the tube red plates and you leave it that way long enough it can actually soften the glass, been there, done that!

Same with leaving a couple layers of skin on the side of a tube. All the major tube manufacturers used to supply little rubber sheaths to techs to pull tubes with, it saves burnt fingers. I still have a couple dried out Sylvania and Zenith pullers somewhere.
0 x

User avatar
nutxo
Newbie
Newbie
Posts: 49
Joined: Tue 08/01/06 2:00 am
Location: Unknown

Post by nutxo »

I replaced the tube and the old tube reallly really brought out the sound. Alas the amp is still doin it though.
0 x

Trout
_
Posts: 542
Joined: Wed 12/07/05 2:00 am
Location: Elburn Illinois

Post by Trout »

This one must have been a degree or 2 over the allowable limit 8O
Image

I have seen worse, but still a good example :D
0 x

User avatar
nutxo
Newbie
Newbie
Posts: 49
Joined: Tue 08/01/06 2:00 am
Location: Unknown

Post by nutxo »

Trout wrote:This one must have been a degree or 2 over the allowable limit 8O
Image

I have seen worse, but still a good example :D
sweet :-)
0 x

User avatar
Michael
Frequent poster
Frequent poster
Posts: 572
Joined: Thu 05/04/06 2:00 am
Location: Charleston
Contact:

Re: how hot should a tube get?

Post by Michael »

nutxo wrote:how hot should a tube get? I mean like scalding hot or just warm to the touch?

This is about how hot power tubes get under NORMAL operation:
http://www.charlestongolf.com/EL84_burn.jpg

And see this closeup:
http://www.charlestongolf.com/EL84_burn2.jpg

Be careful,
Michael 8)
0 x

User avatar
dnichols
Newbie
Newbie
Posts: 72
Joined: Sun 04/16/06 2:00 am
Location: Canada,eh!!

Post by dnichols »

Michael:

The close up shot is awesome........ :lol:
D.
0 x

User avatar
Michael
Frequent poster
Frequent poster
Posts: 572
Joined: Thu 05/04/06 2:00 am
Location: Charleston
Contact:

Post by Michael »

dnichols wrote:Michael:

The close up shot is awesome........ :lol:
D.
Thanks D. Man, I had no idea my arm was so darn harry :!:
0 x

novemberrain
Verbose poster
Verbose poster
Posts: 1191
Joined: Sat 01/22/05 2:00 am

Re: how hot should a tube get?

Post by novemberrain »

Michael wrote:This is about how hot power tubes get under NORMAL operation:
http://www.charlestongolf.com/EL84_burn.jpg

And see this closeup:
http://www.charlestongolf.com/EL84_burn2.jpg

Be careful,
Michael 8)
Yah! I know a muffler burn from a Harley when I see one! That's what ya get when ya drop yer smoke under yer scooter and reach fer it wifout thinkin'! Nice "Mullard" photoshop job, though.

I once gave some skank a ride around the block, she called me back a couple days later lookin' fer money 'cuz supposedly she melted her stockings to her legs on the pipes. Turns out her rent was due...
0 x

Post Reply