Question on zener placement to
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Question on zener placement to
reduce the B+ voltage. Searching on the site, I think I get the basics. My B+ of 360V at pin 3 of V6 is about 15V higher than I'd like it to be. So 3 x 5.6 V 5W zeners in series seems to be in order.
Reading through the material, it seems I can put these three in line with the wire going from the capcan terminal to the board with the stripe side of the zeners facing back to the capcan. Is this correct?
If the placement is correct, will suspending them in the air be enough to cool them?
Thanks.
Bernard
Reading through the material, it seems I can put these three in line with the wire going from the capcan terminal to the board with the stripe side of the zeners facing back to the capcan. Is this correct?
If the placement is correct, will suspending them in the air be enough to cool them?
Thanks.
Bernard
1 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Question on zener placement to
Sounds like you've got a good handle of what you're doing here. The 5W rating is overkill (which is a good thing), especially when you're using 3 Zeners to do the voltage dropping, so heat shouldn't be an issue.
I would be more concerned with vibration. If it's a short distance to the board from the cap can, then it's all good. If not, I'd use a terminal strip in between to give it stability.
I would be more concerned with vibration. If it's a short distance to the board from the cap can, then it's all good. If not, I'd use a terminal strip in between to give it stability.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
Cool, thanks for the feedback Josh. I’m sure when I open it back up i’ll figure some thing out.
Cheers!
Cheers!
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Question on zener placement to
Correct - except the stripe side of all the zeners need to point towards your OR, not the filter cap can.***correction that was meant to say "OT" not "OR"bvayling wrote: ↑Wed 04/15/20 10:58 amreduce the B+ voltage. Searching on the site, I think I get the basics. My B+ of 360V at pin 3 of V6 is about 15V higher than I'd like it to be. So 3 x 5.6 V 5W zeners in series seems to be in order.
Reading through the material, it seems I can put these three in line with the wire going from the capcan terminal to the board with the stripe side of the zeners facing back to the capcan. Is this correct?
0 x
Nature abhors a clean tube amp
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
Thanks Phil.
I thought I understood it but obviously need to do some more reading and retention on zeners.
I had even copied what you just said from a 2011 thread into my notes.....I need to slow down and process better. (Hits self on head.)
I thought I understood it but obviously need to do some more reading and retention on zeners.
I had even copied what you just said from a 2011 thread into my notes.....I need to slow down and process better. (Hits self on head.)
0 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Question on zener placement to
just for confirmation,looking at this symbol which side has the grey/silver band on a zener diode?
You do not have the required permissions to view the files attached to this post.
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Question on zener placement to
The pointed end with the bent bar across it, is the stripe side.
0 x
Nature abhors a clean tube amp
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
Thanks for the clarification, I was getting even more confused...zaphod_phil wrote: ↑Thu 04/16/20 12:29 pmCorrect - except the stripe side of all the zeners need to point towards your OR, not the filter cap can.***correction that was meant to say "OT" not "OR"
For peace of mind at this point, I am guessing that when you say OT, you mean the final destination in the chain of the current flow? (Since the wire in question goes to the board.)
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Question on zener placement to
The issue in clarity here is that I don't know that either of you are speaking about the same method of dropping the voltage. "After the 1st filter cap" can be vague. Maybe a reference diagram would be helpful.bvayling wrote: ↑Fri 04/17/20 8:22 amThanks for the clarification, I was getting even more confused...zaphod_phil wrote: ↑Thu 04/16/20 12:29 pmCorrect - except the stripe side of all the zeners need to point towards your OR, not the filter cap can.***correction that was meant to say "OT" not "OR"
For peace of mind at this point, I am guessing that when you say OT, you mean the final destination in the chain of the current flow? (Since the wire in question goes to the board.)
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Question on zener placement to
yeah this is confusing to me now,the 18V zener on this triwatt is showing the stripe side towards the rectifier not the OT?
so for instance if i place a zener to drop B+ between the can cap filter and OT then the stripe/band side goes to the OT.You do not have the required permissions to view the files attached to this post.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Question on zener placement to
The stripe goes towards the voltage source.
The vagueness is in the actual placements of the Zeners considering that "after the first filter cap" could literally mean any point from between the first two filter caps to the end of the B+ line (which would be silly, but you get my point).
In your example of the Triwatt schematic, D5's stripe is pointed towards the voltage source (which is correct), but it is also before the 1st filter cap. The issue here is that it won't drop voltage as efficiently. In my experience the voltage drop could be as low as 50% of the Zener rating in that position. I do it anyway for logistical reasons, but it's not ideal.
The vagueness is in the actual placements of the Zeners considering that "after the first filter cap" could literally mean any point from between the first two filter caps to the end of the B+ line (which would be silly, but you get my point).
In your example of the Triwatt schematic, D5's stripe is pointed towards the voltage source (which is correct), but it is also before the 1st filter cap. The issue here is that it won't drop voltage as efficiently. In my experience the voltage drop could be as low as 50% of the Zener rating in that position. I do it anyway for logistical reasons, but it's not ideal.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Question on zener placement to
yeah Josh i followed that triwatt orientation with the stripe towards the rectifier except i've placed it between the 1st filter and output transformer as ZP says they are more efficient here.i'm trying to add a pic but my laptop is'nt reading the card!
it's working and dropping the correct voltage.
it's working and dropping the correct voltage.
You do not have the required permissions to view the files attached to this post.
Last edited by geoff 1965 on Fri 04/17/20 2:46 pm, edited 1 time in total.
0 x
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
It seems to me placing the zeners after the filter cap and before the voltage goes to the board makes the most sense.
From what I’ve read, a zener will drop voltage regardless of orientation but will drop it‘s full rated voltage only if placed with the stripe facing “back” towards the voltage source.
I think Phil is using OT as a form of providing direction, as in the voltage comes from the capcan and ultimately winds up at the OT. If I am trying to reduce the B+ It has to be done before it gets to the board, no?
I’ve been wrong before.
From what I’ve read, a zener will drop voltage regardless of orientation but will drop it‘s full rated voltage only if placed with the stripe facing “back” towards the voltage source.
I think Phil is using OT as a form of providing direction, as in the voltage comes from the capcan and ultimately winds up at the OT. If I am trying to reduce the B+ It has to be done before it gets to the board, no?
I’ve been wrong before.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Question on zener placement to
Zeners only drop the rated voltage in one direction. If you orient them the wrong way, they work as a standard diode. For example, a 15V diode will likely drop only about .7V if not oriented correctly.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Question on zener placement to
I'm fascinated that we're using the Triwatt as an example here, as that is actually one of my own amp designs (with much borrowed from Dave Reeves' original Hiwatt designs)geoff 1965 wrote: ↑Fri 04/17/20 9:23 amyeah this is confusing to me now,the 18V zener on this triwatt is showing the stripe side towards the rectifier not the OT?
TriwattSchematic12.pdf
so for instance if i place a zener to drop B+ between the can cap filter and OT then the stripe/band side goes to the OT.
The zener orientation in that schematic is indeed correct, pointing the opposite direction to the rectifiers, D1 -D4. I must now apologise for saying the zener stripe ends should point towards the OT. As some folks now know, I am recovering from a brain injury, due to a combination of brain surgery and radiation treatment. So I often get these mind glitches (aka "brain farts" ), as well as short-term memory losses.
What I really did wrong in the Triwatt design was to place the zener in between the rectifiers and the 50+50uF cap can, C20. I realized my error when testing voltages on the bench, and found that instead of dropping 18V, it was dropping something like 12V, IIRC. However, that drop turned out to be exactly what was wanted, so we left the zener right there in the final design .
1 x
Nature abhors a clean tube amp
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
Phil,
Thanks for chiming in and making sure we stay on the right path here.
I’ve had family members in your situation.
Wishing you well,
Bernard
Thanks for chiming in and making sure we stay on the right path here.
I’ve had family members in your situation.
Wishing you well,
Bernard
1 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Question on zener placement to
thank's for confirming Josh & ZP, i was worried i had it reversed for a while! i placed the zener where you recommended ZP and it's dropping the specified voltage so the filtering does what you said it would.regarding ZP's brain training i've had problems myself the last 2/3 years with a couple of aneurysms on my brain so maybe to be a true 18 watter you need to have some form of brain damage! any of you lads that don't have and are jealous i can call around with my 2lb hammer and oblige you!
0 x
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am
Re: Question on zener placement to
Gents, I am doing the mod now and still confused. If the stripe side of the zener is to be on the side of the voltage source, isn’t the capcan the voltage source?
In Geoff’s pic, the stripe side of the zener is closest to the capcan. If that is correct, then shouldn’t I have the same orientation on my standard 18?
I feel like I am missing something.
In Geoff’s pic, the stripe side of the zener is closest to the capcan. If that is correct, then shouldn’t I have the same orientation on my standard 18?
I feel like I am missing something.
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Question on zener placement to
Yes, to both questions.bvayling wrote: ↑Thu 04/23/20 6:30 pmIf the stripe side of the zener is to be on the side of the voltage source, isn’t the capcan the voltage source?In Geoff’s pic, the stripe side of the zener is closest to the capcan. If that is correct, then shouldn’t I have the same orientation on my standard 18?
1 x
Nature abhors a clean tube amp
-
- Occasional poster
- Posts: 131
- Joined: Sat 03/30/13 12:53 am