Marshall 2061 - Ceriatone Layout Redplate Help
Moderators: JMPGuitars, zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Marshall 2061 - Ceriatone Layout Redplate Help
Can someone help me with next steps here?
bought this "amazing build" but it was redplating
So i'm reading that this is a common issue with this model? Crazy voltages and redplating, now slightttt (have to go to a dark room) but still there. The transformer should be spec'd correctly based on the layout showing the 290 for primary, i'm getting like 300 there , so not really sure why everything is so high. Model used here is PT -290-50 HT-6179-50
So far i've upped the sag resistor from 22 ohm to 34 ohm, the bias resistor is now at 165 ohms
DCV Pins with Tubes giving the same readings
1 N/A
2 V1 - 26mv, v2 33mv
3 14.18V
4 .2mv
5 0
6 N/A
7 375v
8 N/A
9 382v
If i go up to like 210 ohms for the bias resistor, will that kill the plate voltages?
whats next steps here?
love the sound of the circuit, seems like im close here but worried about upping the b+?
maybe add screen resistors?
bought this "amazing build" but it was redplating
So i'm reading that this is a common issue with this model? Crazy voltages and redplating, now slightttt (have to go to a dark room) but still there. The transformer should be spec'd correctly based on the layout showing the 290 for primary, i'm getting like 300 there , so not really sure why everything is so high. Model used here is PT -290-50 HT-6179-50
So far i've upped the sag resistor from 22 ohm to 34 ohm, the bias resistor is now at 165 ohms
DCV Pins with Tubes giving the same readings
1 N/A
2 V1 - 26mv, v2 33mv
3 14.18V
4 .2mv
5 0
6 N/A
7 375v
8 N/A
9 382v
If i go up to like 210 ohms for the bias resistor, will that kill the plate voltages?
whats next steps here?
love the sound of the circuit, seems like im close here but worried about upping the b+?
maybe add screen resistors?
You do not have the required permissions to view the files attached to this post.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
As you can see on your bias calculator screenshot, the maximum for EL84s is 12W, and you're at nearly 15W.
Your cathode voltage is too high, and you need to adjust the cathode resistor value to bias them closer to where they should be. Your 20W amp is pushing 30W, that's dangerous.
Also, your plates are lower than your screen voltages. That's no good. Pin 9 should show a lower voltage than pin 7. I would add a 1K 3W resistor going to pin 9 and see where that puts you.
Most transformers rated at 290 will go to around 300 with modern electricity typically around 120V instead of 110 or 115 depending on what the transformer is expecting.
Pins 4 and 5 are your heaters on the power tubes, and you would use ACV to test them.
Thanks,
Josh
Your cathode voltage is too high, and you need to adjust the cathode resistor value to bias them closer to where they should be. Your 20W amp is pushing 30W, that's dangerous.
Also, your plates are lower than your screen voltages. That's no good. Pin 9 should show a lower voltage than pin 7. I would add a 1K 3W resistor going to pin 9 and see where that puts you.
Most transformers rated at 290 will go to around 300 with modern electricity typically around 120V instead of 110 or 115 depending on what the transformer is expecting.
Pins 4 and 5 are your heaters on the power tubes, and you would use ACV to test them.
Thanks,
Josh
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
That PT is a good one for this, its the Heyboer 6197.
1 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Re: Marshall 2061 - Ceriatone Layout Redplate Help
The screen grids control the behaviour of pentodes and tetrodes. The screen voltages first need to be reduced here, to return everything to normal operation.
2 x
Nature abhors a clean tube amp
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Marshall 2061 - Ceriatone Layout Redplate Help
the 20 watters do push the el84's and i think that will give the amp it's certain character,your screen voltage needs to be addressed as mentioned earlier but actually your plate voltage is the same as this one from the downloads! have a look and check off your voltages on the tubes and B+ rail in comparison,good luck.
You do not have the required permissions to view the files attached to this post.
0 x
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
so i was thinking of zeners to drop the b+ down about 20-30v, or upping the sag resister to 220 ohm, but i hear u the voltages are the same as this schematic minus the screens, can anyone answer the "why" and "how to resolve" without changing the tone too much, just don't want to redplate, seems im 20% over 100% :/
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
What is your B+ reading?l4ent wrote: ↑Wed 05/20/20 1:19 pmso i was thinking of zeners to drop the b+ down about 20-30v, or upping the sag resister to 220 ohm, but i hear u the voltages are the same as this schematic minus the screens, can anyone answer the "why" and "how to resolve" without changing the tone too much, just don't want to redplate, seems im 20% over 100% :/
What is your current cathode resistor value?
Add a 1K 3W resistor to the voltage feeding pin 9 of the power tubes. Or better yet, separate them, and add a 1K 3W resistor to Pin 9 of each tube connected to the voltage source they previously shared. Then recheck the voltages.
Thanks,
Josh
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
Isn’t my b+ pin 7, 375v?JMPGuitars wrote: ↑Wed 05/20/20 2:07 pmWhat is your B+ reading?l4ent wrote: ↑Wed 05/20/20 1:19 pmso i was thinking of zeners to drop the b+ down about 20-30v, or upping the sag resister to 220 ohm, but i hear u the voltages are the same as this schematic minus the screens, can anyone answer the "why" and "how to resolve" without changing the tone too much, just don't want to redplate, seems im 20% over 100% :/
What is your current cathode resistor value?
Add a 1K 3W resistor to the voltage feeding pin 9 of the power tubes. Or better yet, separate them, and add a 1K 3W resistor to Pin 9 of each tube connected to the voltage source they previously shared. Then recheck the voltages.
Thanks,
Josh
165 ohms for cathode resistor.
I will retake those measurements if I make mods I just want to be sure I’m making the “right” ones while staying true to the design.
I will consider adding screen resistors but as I understand it will affect the tone. I unserstand that pin 9 should be lower than 7 so this is a way to do it but looking at the schematic those voltages are actually about equal. I’m trying to understand why if everything is specd exactly to the layout why these mods are necessary or If something is off. As the transformer is specd the same and the parts used match the layout and schematics found on the net.
I could use the zener diodes on the center tap to drop b+ Which would be a fun little thing but according to the charts the high b+ isn’t a problem, should I do this?
it’s that the screen is higher which is causing to redplate. But the og does not have screen resistors and buying the 2061 or ceriatone or other clone will not have screen resistors. I understand how adding them will help but concerned about tone as this circuit just sounds so good and they manage to run without em. Do I need to add them?
I also understand I can increase the sag resistor to 220 and go up from there to drop the b+ To better levels and create more sag / get a rectifier tube which could be fun to add there cause I think there’s space but then og does not have this, do I need to increase sag resistor? This will affect tone surely from the specd 22/30ohm.
Also increasing the bias resistor to maybe 220 should get it closer to where I need to be but concerned about rising b+. I’m thinking this is the next step?
I’m also thinking that based on these responses, just dropping the screen voltage by adding these resistors (while yes changing tone a bit) will fix the red plate? Is that the simple solution to start?
I’m not sure where to start here.
If someone could answer those or help me understand further what the real “next step” is that would be great.
I see these “solutions” but it strikes me odd it needs to be so different from all of these specs I’m seeing. Shouldn’t it be achievable while being close to the product sold by these companies? Also since there seem to be many options I want to know the best route to take while maintaining this awesome sound I’m hearing
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
No, that's your plate voltage, which is correct.
According to the schematic posted above, the B+ is supposed to be 385V, then drops to 370V after the first filter caps. B+ is the rectified voltage going to the filter caps.
375 and 370 are not the same. The rule for pentodes is that the screen voltage should be lower than the plate voltage. If you want the correct tone for the amp, you must lower the screen voltage. The screen resistors also add a layer of protection.l4ent wrote: ↑Wed 05/20/20 3:19 pmI will consider adding screen resistors but as I understand it will affect the tone. I unserstand that pin 9 should be lower than 7 so this is a way to do it but looking at the schematic those voltages are actually about equal. I’m trying to understand why if everything is specd exactly to the layout why these mods are necessary or If something is off. As the transformer is specd the same and the parts used match the layout and schematics found on the net.
Often these small changes in voltages are due to the tubes themselves. Other times it's a silly thing like forgetting to include screen resistors in a schematic.
Your B+ is still unknown to us, so I don't know if you need to drop it. Your plate voltages are good right now.l4ent wrote: ↑Wed 05/20/20 3:19 pmI could use the zener diodes on the center tap to drop b+ Which would be a fun little thing but according to the charts the high b+ isn’t a problem, should I do this?
it’s that the screen is higher which is causing to redplate. But the og does not have screen resistors and buying the 2061 or ceriatone or other clone will not have screen resistors. I understand how adding them will help but concerned about tone as this circuit just sounds so good and they manage to run without em. Do I need to add them?
If you're trying to capture the "OG" tone, then you need to pay attention to your voltages, not what clone amps have or don't have.
No, this is backwards. Raising the resistor value will raise the voltage. You need to reduce the resistor value to drop the voltage. Try 150R or 130R. Measure your B+ before and after.l4ent wrote: ↑Wed 05/20/20 3:19 pmI also understand I can increase the sag resistor to 220 and go up from there to drop the b+ To better levels and create more sag / get a rectifier tube which could be fun to add there cause I think there’s space but then og does not have this, do I need to increase sag resistor? This will affect tone surely from the specd 22/30ohm.
Also increasing the bias resistor to maybe 220 should get it closer to where I need to be but concerned about rising b+. I’m thinking this is the next step?
Steps as I've stated above:l4ent wrote: ↑Wed 05/20/20 3:19 pmI’m also thinking that based on these responses, just dropping the screen voltage by adding these resistors (while yes changing tone a bit) will fix the red plate? Is that the simple solution to start?
I’m not sure where to start here.
If someone could answer those or help me understand further what the real “next step” is that would be great.
I see these “solutions” but it strikes me odd it needs to be so different from all of these specs I’m seeing. Shouldn’t it be achievable while being close to the product sold by these companies? Also since there seem to be many options I want to know the best route to take while maintaining this awesome sound I’m hearing
1. Take your voltages, including your correct B+.
2. Adjust your cathode resistor to get to a better bias point.
3. Add 1K 3W screen resistors.
3. Take all your voltages again and share them here. Compare them to the schematic voltages.
Changing the screen voltages to the correct voltage is the right thing to do. I don't know that you would be able to perceive a tonal change. In any case, the correct voltage is generally the way it's supposed to sound.
The only specs that matter are the schematic. Making those changes will get you closer to those specs. That's what you want, and should give you the ideal tone, if you're trying to match the original. What people sell is an entirely different discussion, and doesn't fix your amp. A lot of people sell a lot of silly things for silly reasons.
Thanks,
Josh
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
I just figured that if they make it work without screen resistors there should be a way but I also don’t know anything lolJMPGuitars wrote: ↑Wed 05/20/20 5:38 pmNo, that's your plate voltage, which is correct.
According to the schematic posted above, the B+ is supposed to be 385V, then drops to 370V after the first filter caps. B+ is the rectified voltage going to the filter caps.
375 and 370 are not the same. The rule for pentodes is that the screen voltage should be lower than the plate voltage. If you want the correct tone for the amp, you must lower the screen voltage. The screen resistors also add a layer of protection.l4ent wrote: ↑Wed 05/20/20 3:19 pmI will consider adding screen resistors but as I understand it will affect the tone. I unserstand that pin 9 should be lower than 7 so this is a way to do it but looking at the schematic those voltages are actually about equal. I’m trying to understand why if everything is specd exactly to the layout why these mods are necessary or If something is off. As the transformer is specd the same and the parts used match the layout and schematics found on the net.
Often these small changes in voltages are due to the tubes themselves. Other times it's a silly thing like forgetting to include screen resistors in a schematic.
Your B+ is still unknown to us, so I don't know if you need to drop it. Your plate voltages are good right now.l4ent wrote: ↑Wed 05/20/20 3:19 pmI could use the zener diodes on the center tap to drop b+ Which would be a fun little thing but according to the charts the high b+ isn’t a problem, should I do this?
it’s that the screen is higher which is causing to redplate. But the og does not have screen resistors and buying the 2061 or ceriatone or other clone will not have screen resistors. I understand how adding them will help but concerned about tone as this circuit just sounds so good and they manage to run without em. Do I need to add them?
If you're trying to capture the "OG" tone, then you need to pay attention to your voltages, not what clone amps have or don't have.
No, this is backwards. Raising the resistor value will raise the voltage. You need to reduce the resistor value to drop the voltage. Try 150R or 130R. Measure your B+ before and after.l4ent wrote: ↑Wed 05/20/20 3:19 pmI also understand I can increase the sag resistor to 220 and go up from there to drop the b+ To better levels and create more sag / get a rectifier tube which could be fun to add there cause I think there’s space but then og does not have this, do I need to increase sag resistor? This will affect tone surely from the specd 22/30ohm.
Also increasing the bias resistor to maybe 220 should get it closer to where I need to be but concerned about rising b+. I’m thinking this is the next step?
Steps as I've stated above:l4ent wrote: ↑Wed 05/20/20 3:19 pmI’m also thinking that based on these responses, just dropping the screen voltage by adding these resistors (while yes changing tone a bit) will fix the red plate? Is that the simple solution to start?
I’m not sure where to start here.
If someone could answer those or help me understand further what the real “next step” is that would be great.
I see these “solutions” but it strikes me odd it needs to be so different from all of these specs I’m seeing. Shouldn’t it be achievable while being close to the product sold by these companies? Also since there seem to be many options I want to know the best route to take while maintaining this awesome sound I’m hearing
1. Take your voltages, including your correct B+.
2. Adjust your cathode resistor to get to a better bias point.
3. Add 1K 3W screen resistors.
3. Take all your voltages again and share them here. Compare them to the schematic voltages.
Changing the screen voltages to the correct voltage is the right thing to do. I don't know that you would be able to perceive a tonal change. In any case, the correct voltage is generally the way it's supposed to sound.
The only specs that matter are the schematic. Making those changes will get you closer to those specs. That's what you want, and should give you the ideal tone, if you're trying to match the original. What people sell is an entirely different discussion, and doesn't fix your amp. A lot of people sell a lot of silly things for silly reasons.
Thanks,
Josh
So far I’ve upped the cathode resistor to reduce redplating. You’re saying I need to bring it back closer to 130 from the current 160?
Does this help give all the volts needed? This is a user made schematic I found of a 2061x that I followed and the components match up to this. I could also make one off the layout if that would help. My voltages are in green [ Not sure if it makes a diff but the layout calls for 47uf 455v whereas mines got four 47uf 400v capacitors. Let me know if I need to remeasure the Pins.
You do not have the required permissions to view the files attached to this post.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
If your tubes were worse before you raised the resistor, then you probably do need to raise the resistance higher. Just make sure to calculate the dissipation. You want to get your tubes to dissipate a total of around 20 watts. You're currently at 30W, which is way too high. I don't know what your target cathode current is for that circuit, but where you're at is high.l4ent wrote: ↑Wed 05/20/20 8:20 pmI just figured that if they make it work without screen resistors there should be a way but I also don’t know anything lol
So far I’ve upped the cathode resistor to reduce redplating. You’re saying I need to bring it back closer to 130 from the current 160?
Does this help give all the volts needed? This is a user made schematic I found of a 2061x that I followed and the components match up to this. I could also make one off the layout if that would help. My voltages are in green [77C84915-4D6B-4C92-AC81-D9702108B482.jpeg Not sure if it makes a diff but the layout calls for 47uf 455v whereas mines got four 47uf 400v capacitors. Let me know if I need to remeasure the Pins.
I would swap out those 400V caps for 500V. You never want to be that close to the voltage limit.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
Am i not taking the HT reading right?
You do not have the required permissions to view the files attached to this post.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
HT is the taps on the PT for your AC voltage that go the rectifier. Where are you reading those voltages? 18watt transformers are usually rated 290-0-290, and with modern voltage typically see 300-0-300 (assuming a center tap is present).
The B+ is that voltage rectified to DC. Your OT CT reading is usually the same as the B+ reading.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Marshall 2061 - Ceriatone Layout Redplate Help
That is correct. Those HT wires going to the rectifier tube are the only AC readings taken at the tubes (besides the heaters, but that's usually taken at the PT).
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Marshall 2061 - Ceriatone Layout Redplate Help
is your pin9 voltage still higher than pin7 on the el84's? the 470ohm resistor is your screen resistor so you need to check its wired correctly i.e. your B+ comes through the sag resistor and into the output transformer centre tap then passes through the 470ohm into the screens.
0 x
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
geoff 1965 wrote: ↑Fri 05/22/20 11:44 amis your pin9 voltage still higher than pin7 on the el84's? the 470ohm resistor is your screen resistor so you need to check its wired correctly i.e. your B+ comes through the sag resistor and into the output transformer centre tap then passes through the 470ohm into the screens.
I'm seeing the sag resistor go to standby, standby goes to the 470ohm which is connected to both the OT CT and the end of the 470 ohm screengeoff 1965 wrote: ↑Fri 05/22/20 11:44 amyour B+ comes through the sag resistor and into the output transformer centre tap then passes through the 470ohm into the screens.
You do not have the required permissions to view the files attached to this post.
0 x
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am
Re: Marshall 2061 - Ceriatone Layout Redplate Help
now im getting
V3 pin 7 371
pin 9 378
V4 7 371
pin 9 378
so yes 9 is still higher
V3 pin 7 371
pin 9 378
V4 7 371
pin 9 378
so yes 9 is still higher
0 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: Marshall 2061 - Ceriatone Layout Redplate Help
okay so what voltage do you have going into and the other side of the 470 ohm?
0 x
-
- Unrated
- Posts: 11
- Joined: Tue 05/19/20 9:03 am