to standby switch.. or not to standby switch
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
- Bieworm
- Verbose Moderator
- Posts: 2308
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
to standby switch.. or not to standby switch
that's the question..
Is there any plausible reason to use your standby switch? I read a lot that it's completely not necessary.
The problem would be 'cathode stripping' by stressing the cold tube with high voltage. I also read that one can even begin to think about this phenomenon at a 1000V+, which never occurs in a guitar amplifier.
Any other thoughts? I do not always use it to be honest...
Is there any plausible reason to use your standby switch? I read a lot that it's completely not necessary.
The problem would be 'cathode stripping' by stressing the cold tube with high voltage. I also read that one can even begin to think about this phenomenon at a 1000V+, which never occurs in a guitar amplifier.
Any other thoughts? I do not always use it to be honest...
0 x
"THIS should be played at high volume..preferably in a residential area"
-
- Superior Amp Tech
- Posts: 750
- Joined: Fri 01/08/10 2:00 am
- Location: Scotland
Re: to standby switch.. or not to standby switch
This thread is like Hailey's Comet. It appears at predictable times and creates fear in the unwary then brings unending argument about what it is.
My view:
You are probably correct that stripping is a myth in guitar amps. For me a standby switch on a valve amp is a convenience as you can head off and make a cup of tea, pour a beer, or whatever and come back and play straight away. The test is whether you need one on a ss amp. The answer is no for convenience at least. Since stripping is a myth you can leave it on standby for long periods with no harm done. Just in case I have a large value resistor across the standby switch allowing a low level voltage to run while on standby. Just in case the myth is fact. Call me superstitious if you like. But then there is magic in those valves my son.
So.. I like a standby switch. But I do not have one on my Champ. I cannot explain that.
Dd
My view:
You are probably correct that stripping is a myth in guitar amps. For me a standby switch on a valve amp is a convenience as you can head off and make a cup of tea, pour a beer, or whatever and come back and play straight away. The test is whether you need one on a ss amp. The answer is no for convenience at least. Since stripping is a myth you can leave it on standby for long periods with no harm done. Just in case I have a large value resistor across the standby switch allowing a low level voltage to run while on standby. Just in case the myth is fact. Call me superstitious if you like. But then there is magic in those valves my son.
So.. I like a standby switch. But I do not have one on my Champ. I cannot explain that.
Dd
3 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: to standby switch.. or not to standby switch
I assume you've read Merlin's website regarding this. He points out plenty of interesting theory, including workarounds like the one Dd mentioned. I'm relatively indifferent about standby switches, but they're generally expected, and I like switches, so I keep them.
If this were more of a concern, I think we'd hear a lot more about tube rectifier failure, but that's not fantastically common. Eventually they die like any other tube, but I can't think of a single time in 30 years of playing where a rectifier tube actually needed to be replaced. I'd be more likely to consider the resistor on the switch for an amp whose rectifier tube costs more than $10. Or if I wasted money on NOS stuff.
If this were more of a concern, I think we'd hear a lot more about tube rectifier failure, but that's not fantastically common. Eventually they die like any other tube, but I can't think of a single time in 30 years of playing where a rectifier tube actually needed to be replaced. I'd be more likely to consider the resistor on the switch for an amp whose rectifier tube costs more than $10. Or if I wasted money on NOS stuff.
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- Bieworm
- Verbose Moderator
- Posts: 2308
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: to standby switch.. or not to standby switch
My thoughts exactly.JMPGuitars wrote: ↑Wed 04/15/20 10:04 amI assume you've read Merlin's website regarding this. He points out plenty of interesting theory, including workarounds like the one Dd mentioned. I'm relatively indifferent about standby switches, but they're generally expected, and I like switches, so I keep them.
If this were more of a concern, I think we'd hear a lot more about tube rectifier failure, but that's not fantastically common. Eventually they die like any other tube, but I can't think of a single time in 30 years of playing where a rectifier tube actually needed to be replaced. I'd be more likely to consider the resistor on the switch for an amp whose rectifier tube costs more than $10. Or if I wasted money on NOS stuff.
BTW I hear just as often people complain about noisy NOS tubes than I hear people rave on about them.
It's cool to have an oldskool American tube , but there is something kinky sexy about them russian tubes too. But mostly I buy JJ preamp tubes, and the EL84 my preferation is on mil spec sovteks. They just don't crap out...
1 x
"THIS should be played at high volume..preferably in a residential area"
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: to standby switch.. or not to standby switch
The only time I bother with NOS is for things like tube mics, but then I still only get inexpensive ones...and usually when I get NOS it's because they're not in production anymore.Bieworm wrote: ↑Wed 04/15/20 12:12 pmMy thoughts exactly.
BTW I hear just as often people complain about noisy NOS tubes than I hear people rave on about them.
It's cool to have an oldskool American tube , but there is something kinky sexy about them russian tubes too. But mostly I buy JJ preamp tubes, and the EL84 my preferation is on mil spec sovteks. They just don't crap out...
JJ preamp tubes are good, but never use their EL84 power tubes (they're trash). For EL84s I've had good luck with new production Mullard, and Tung Sol. TAD is okay too, but I think usually overpriced and selling too much mojo. I'm not personally into EH or Sovtek. Neither sound great to me, though I have nothing against them really.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- Bieworm
- Verbose Moderator
- Posts: 2308
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: to standby switch.. or not to standby switch
In my fenders I use tung sol 5881 reissues. They sound big in those amps. I remember having a bassman with TAD 6l6wgb and remember being very impressed by them.JMPGuitars wrote: ↑Wed 04/15/20 12:19 pmThe only time I bother with NOS is for things like tube mics, but then I still only get inexpensive ones...and usually when I get NOS it's because they're not in production anymore.Bieworm wrote: ↑Wed 04/15/20 12:12 pmMy thoughts exactly.
BTW I hear just as often people complain about noisy NOS tubes than I hear people rave on about them.
It's cool to have an oldskool American tube , but there is something kinky sexy about them russian tubes too. But mostly I buy JJ preamp tubes, and the EL84 my preferation is on mil spec sovteks. They just don't crap out...
JJ preamp tubes are good, but never use their EL84 power tubes (they're trash). For EL84s I've had good luck with new production Mullard, and Tung Sol. TAD is okay too, but I think usually overpriced and selling too much mojo. I'm not personally into EH or Sovtek. Neither sound great to me, though I have nothing against them really.
But for EL84 's I tend to trust only the russian mil spec'd tubes such as the EL84 M
Probably because I used them in vox amps..and certainly the reverb driver of my VK. That one just burns regular EL84 's
0 x
"THIS should be played at high volume..preferably in a residential area"
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: to standby switch.. or not to standby switch
You have an amp with an EL84 reverb driver?? I've never heard that. Sample please.Bieworm wrote: ↑Wed 04/15/20 3:13 pmIn my fenders I use tung sol 5881 reissues. They sound big in those amps. I remember having a bassman with TAD 6l6wgb and remember being very impressed by them.
But for EL84 's I tend to trust only the russian mil spec'd tubes such as the EL84 M
Probably because I used them in vox amps..and certainly the reverb driver of my VK. That one just burns regular EL84 's
Supposedly EL84Ms give higher headroom/less gain compared to standard EL84s. I dunno if I believe it.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- Bieworm
- Verbose Moderator
- Posts: 2308
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: to standby switch.. or not to standby switch
A VK has a 63 reverb tank built in. It's powered by an EL84. Later they went to 6v6, but if you use an EL84 M the problem is over. The el84 M is supposed to handle higher voltages...sturdierJMPGuitars wrote: ↑Wed 04/15/20 4:01 pmYou have an amp with an EL84 reverb driver?? I've never heard that. Sample please.Bieworm wrote: ↑Wed 04/15/20 3:13 pmIn my fenders I use tung sol 5881 reissues. They sound big in those amps. I remember having a bassman with TAD 6l6wgb and remember being very impressed by them.
But for EL84 's I tend to trust only the russian mil spec'd tubes such as the EL84 M
Probably because I used them in vox amps..and certainly the reverb driver of my VK. That one just burns regular EL84 's
Supposedly EL84Ms give higher headroom/less gain compared to standard EL84s. I dunno if I believe it.
0 x
"THIS should be played at high volume..preferably in a residential area"
-
- Newbie
- Posts: 88
- Joined: Tue 02/09/16 12:38 pm
Re: to standby switch.. or not to standby switch
Sorry if I start the topic again, but I was just looking at the Lite IIb stand-by switch after reading Merlin's website. So, why is the stand-by switch before the first reservoir cap and not after?
As well, if I want leave out the stand by switch, I would just connect pin 3 of the EZ81 to the first reservoir cap, right? Is the 220K resistor still needed then?
Thanks, I hope this is not an annoying topic.
As well, if I want leave out the stand by switch, I would just connect pin 3 of the EZ81 to the first reservoir cap, right? Is the 220K resistor still needed then?
Thanks, I hope this is not an annoying topic.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3969
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: to standby switch.. or not to standby switch
Yes.Riffmonster wrote: ↑Sat 04/18/20 3:38 pmAs well, if I want leave out the stand by switch, I would just connect pin 3 of the EZ81 to the first reservoir cap, right? Is the 220K resistor still needed then?
The 220K is still needed. It's a bleeder resistor to drain the filter caps when the amp is shut off.
2 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
-
- Newbie
- Posts: 88
- Joined: Tue 02/09/16 12:38 pm
Re: to standby switch.. or not to standby switch
Thanks, just realized that too!JMPGuitars wrote: ↑Sat 04/18/20 4:06 pmYes.Riffmonster wrote: ↑Sat 04/18/20 3:38 pmAs well, if I want leave out the stand by switch, I would just connect pin 3 of the EZ81 to the first reservoir cap, right? Is the 220K resistor still needed then?
The 220K is still needed. It's a bleeder resistor to drain the filter caps when the amp is shut off.
1 x
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: to standby switch.. or not to standby switch
I like to put my standby switch in the rotary SPST in my Pre-PIMV pot. I use these:
https://www.tubedepot.com/products/alph ... ith-switch .
It's nice because you can just turn your MV all the way down and click a little further into standby. No pop. I haven't seen a dual pot with a rotary switch so it wouldn't work for a post-PIMV which a lot of people like.
https://www.tubedepot.com/products/alph ... ith-switch .
It's nice because you can just turn your MV all the way down and click a little further into standby. No pop. I haven't seen a dual pot with a rotary switch so it wouldn't work for a post-PIMV which a lot of people like.
0 x
-
- Unrated
- Posts: 17
- Joined: Thu 11/24/16 11:14 am
Re: to standby switch.. or not to standby switch
with tube rectification, i never use it. Never had an issue. done it for years. But, do whatever makes you comfy, right?
0 x
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: to standby switch.. or not to standby switch
So you only use it to preheat the tubes? You know, there's a way to wire two switches so that whichever one you throw first heats the filaments. Then, throwing the other one engages B+. I think this might require DPDT switches, but i haven't looked at that circuit in a while.
0 x
-
- Occasional poster
- Posts: 195
- Joined: Mon 05/18/20 8:09 pm
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: to standby switch.. or not to standby switch
On my current build the real estate is limited so I skipped the standby switch. I actually thought about skipping the mains power switch too, since I'm using a detachable IEC inlet socket, but that seemed extreme and I did have room for one switch; so I did include a power switch. Anyway I chatted with an engineer at Ametherm about foregoing the standby switch and soft starting the tubes with an NTC thermistor; he recommended placing one in the B+ line as an inrush current limiter, in series on the capacitor bus. For amps up to and including 100W, with a 405V bus and up to about 100µF reservoir capacitance, the part is Ametherm SL15 12102. This provides a soft start, extending tube filament life and also protecting the transformer secondary. Since they sent me a few free samples, I decided to also place a second one on the primary side between my fuse and my on/off switch to protect the PT from AC inrush spikes. They're only about a buck at Mouser: https://www.mouser.com/ProductDetail/Am ... wSQA%3D%3D
0 x
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: to standby switch.. or not to standby switch
I'll go on record here as saying there's absolutely no reason to soft-start tubes operating at voltages less than 1KV. I do include soft-start with SET amps using 1KV or more, but nothing below that. And just to add some empirical data, I've purchased numerous hi-fi amps with SS rectifiers from the '60s that clearly had thousands of hours on them. Nearly all still had their original output tubes, and those tubes never showed any indication of damage or unusual deterioration after all those years of operation. This is at voltages up to nearly 500V.
I admit that I'm adding a 5AR4 to my latest project, but that's strictly to protect the power supply when there's no load (cold tubes). I'm using 450V caps, and the supply exceeds that under no-load conditions by 20V-30V. The surge rating of the caps will probably cover it, but I decided not to take the chance. FWIW, quite a bit of audio gear was designed like that in the early days. Manufacturers often recommended against powering their gear without the tubes for that reason.
I admit that I'm adding a 5AR4 to my latest project, but that's strictly to protect the power supply when there's no load (cold tubes). I'm using 450V caps, and the supply exceeds that under no-load conditions by 20V-30V. The surge rating of the caps will probably cover it, but I decided not to take the chance. FWIW, quite a bit of audio gear was designed like that in the early days. Manufacturers often recommended against powering their gear without the tubes for that reason.
0 x