Parasitic oscillation problem untraceable
Moderators: JMPGuitars, zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Parasitic oscillation problem untraceable
If you could supply a schematic version including all the changes you've done, that would help too.
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
This looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
I'll post voltages later on todayIf you could supply a schematic version including all the changes you've done, that would help too.
You do not have the required permissions to view the files attached to this post.
0 x
"THIS should be played at high volume..preferably in a residential area"
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: Parasitic oscillation problem untraceable
For that waveform to be really useful, he needs to drop the amplitude significantly (assuming that's what's driving the amplitude read by the scope). The signal generator amplitude should be 125mV. He should also stretch the time base a little so we can see the rise and fall better, in which case the crossover distortion will likely be more visible (if present). At its current amplitude, he could be introducing problems that aren't relevant to actual circuit voltage levels (assuming his source is set too high).TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
Bieworm, what's the signal generator amplitude set to? Where is the signal being inserted?
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
Have you removed the Zener at the output cathodes? I think that's needed in order to be sure bias destabilization isn't playing a role in this. I don't see how it's possible to have a softer breakdown If the cathodes have 30V DC when pushed.
Jack
Jack
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
It's a 1kHz tone generated by a signal generator.TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
0 x
"THIS should be played at high volume..preferably in a residential area"
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
Gotcha. Am I correct in assuming this sounds fizzy? If so, is it the same tonal quality as the fizz you're hearing when you play?Bieworm wrote: ↑Thu 01/07/21 12:18 pmIt's a 1kHz tone generated by a signal generator.TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
Don't know. It's hooked to an 8 ohm 50W dummyload. But at those settings I think It's fizzing the crap out of the amp. I don't think my ears could handle 1kHz at the input with the volume of the amp on 6TriodeLuvr wrote: ↑Thu 01/07/21 12:27 pmGotcha. Am I correct in assuming this sounds fizzy? If so, is it the same tonal quality as the fizz you're hearing when you play?Bieworm wrote: ↑Thu 01/07/21 12:18 pmIt's a 1kHz tone generated by a signal generator.TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
0 x
"THIS should be played at high volume..preferably in a residential area"
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
What's the amplitude of that signal? There are multiple voltage readings on the display, none of them seem right for the signal to be so clipped. What is the Volts/Div?
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
What do you mean? On the volume dial? I have to measure that wit the DMMJMPGuitars wrote: ↑Thu 01/07/21 12:00 pmFor that waveform to be really useful, he needs to drop the amplitude significantly (assuming that's what's driving the amplitude read by the scope). The signal generator amplitude should be 125mA. He should also stretch the time base a little so we can see the rise and fall better, in which case the crossover distortion will likely be more visible (if present). At its current amplitude, he could be introducing problems that aren't relevant to actual circuit voltage levels (assuming his source is set too high).TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
Bieworm, what's the signal generator amplitude set to? Where is the signal being inserted?
I plugged in an unused jack at the input and connected that to the signal generator with a probe. I saw DLabs do it once ..I think?
0 x
"THIS should be played at high volume..preferably in a residential area"
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
I'm trying to figure out how large that signal is. I've never seen a digital scope that doesn't display the Volts/Div setting on the screen somewhere.
1 x
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
Just to make the point, one of the readouts on the screen says the voltage delta is 1.96V peak-to-peak. If that's real, the amp is clipping at a very low signal level. If it's a measurement after a 10:1 probe that the scope doesn't know about, it's still low. 19.6V p-p is about 6.9V RMS, or about 6W into 8 ohms. That should be nowhere near output clipping for this amp.
Jack
Jack
1 x
-
- Newbie
- Posts: 44
- Joined: Thu 09/17/20 2:56 pm
Re: Parasitic oscillation problem untraceable
When I am scoping something out, I will hook a test lead up in the first channel to the input jack where I am injecting the test signal. Make sure that is at the correct level before doing anything else. If you aren't sure, then plug a guitar in and play while monitoring input voltage on your scope at the input jack. That will tell you what range you need to be in.
Then, you hook up the second test lead to the output or any other part of the circuit you need to test. Before probing very high voltage, make sure your leads can handle that. I bought a 100x lead to use on the plates of the output tubes. You should be able to set your scope channel on the padding level of your particular probes.
If you see oscillation on the output, then I would start at the front end and work your way through the signal path. Note measurements at the grid and then output of that preamp stage to see if it is amplifying or buffering like you would expect. You will be able to see where the oscillation shows itself and you can narrow down your search to that block of the circuit.
Does your scope have an FFT function? You can use that to test the harmonics on the output signal. You just have to set the range of the FFT reading to the appropriate ratio for your 1K signal. On my scope I have to change the test signal to 1.5K to make everything line up cleanly.
Don't give up, just attack this strategically.
-Dan
Then, you hook up the second test lead to the output or any other part of the circuit you need to test. Before probing very high voltage, make sure your leads can handle that. I bought a 100x lead to use on the plates of the output tubes. You should be able to set your scope channel on the padding level of your particular probes.
If you see oscillation on the output, then I would start at the front end and work your way through the signal path. Note measurements at the grid and then output of that preamp stage to see if it is amplifying or buffering like you would expect. You will be able to see where the oscillation shows itself and you can narrow down your search to that block of the circuit.
Does your scope have an FFT function? You can use that to test the harmonics on the output signal. You just have to set the range of the FFT reading to the appropriate ratio for your 1K signal. On my scope I have to change the test signal to 1.5K to make everything line up cleanly.
Don't give up, just attack this strategically.
-Dan
1 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
Josh... how do I set the amplitude to mA? With the DMM I can only measure VDC on the output of the generator. Measure it with the scope?JMPGuitars wrote: ↑Thu 01/07/21 12:00 pmFor that waveform to be really useful, he needs to drop the amplitude significantly (assuming that's what's driving the amplitude read by the scope). The signal generator amplitude should be 125mA. He should also stretch the time base a little so we can see the rise and fall better, in which case the crossover distortion will likely be more visible (if present). At its current amplitude, he could be introducing problems that aren't relevant to actual circuit voltage levels (assuming his source is set too high).TriodeLuvr wrote: ↑Thu 01/07/21 11:07 amThis looks like it might contain strong higher-order harmonics. Is this clipping occurring at the output tubes, or is it in one of the preamp stages? Do the grids of the phase inverter look like this? And what's creating a 1.0000 kHz tone?
Bieworm, what's the signal generator amplitude set to? Where is the signal being inserted?
I measure at an empty jackplug that's put in the input of the amp. As if it were a guitar..
Here's the voltage chart that corresponds with the schematics I sent today.
You do not have the required permissions to view the files attached to this post.
0 x
"THIS should be played at high volume..preferably in a residential area"
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
mA isn't amplitude. I'm pretty sure that was a typo.
1 x
- TriodeLuvr
- Frequent poster
- Posts: 616
- Joined: Tue 10/16/18 11:19 am
Re: Parasitic oscillation problem untraceable
Just want to add, the waveform at the output looks like preamp clipping. Output stage clipping usually leads to spikes and other anomalies that aren't so symmetrical in appearance. I think you might be driving the amp too hard with the generator.
Jack
Jack
1 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
I'm testing right now with 125mV output of the generator.TriodeLuvr wrote: ↑Thu 01/07/21 2:51 pmJust want to add, the waveform at the output looks like preamp clipping. Output stage clipping usually leads to spikes and other anomalies that aren't so symmetrical in appearance. I think you might be driving the amp too hard with the generator.
Jack
Last edited by Bieworm on Thu 01/07/21 4:24 pm, edited 1 time in total.
0 x
"THIS should be played at high volume..preferably in a residential area"
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
Input stage 2 OD channel
You do not have the required permissions to view the files attached to this post.
Last edited by Bieworm on Thu 01/07/21 4:28 pm, edited 2 times in total.
0 x
"THIS should be played at high volume..preferably in a residential area"
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
Input grid stage 3 OD
You do not have the required permissions to view the files attached to this post.
Last edited by Bieworm on Thu 01/07/21 4:32 pm, edited 4 times in total.
0 x
"THIS should be played at high volume..preferably in a residential area"
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Parasitic oscillation problem untraceable
Input grid 6V6's
You do not have the required permissions to view the files attached to this post.
0 x
"THIS should be played at high volume..preferably in a residential area"