18w S/C with SS rectifier?
Moderators: zaphod_phil, CurtissRobin, colossal
-
- Occasional poster
- Posts: 141
- Joined: Thu 08/28/03 2:00 am
- Location: 5min South East of St. Louis, MO
- Contact:
18w S/C with SS rectifier?
I'm in the process of building a 18w S/C, but i am trying to conserve costs here and am wondering how it would sound with a SS rectifier... Also, i have a PT that puts out about 285-0-285 and i'm wondering if that would be enough to get this project moving along. The PT was from an old Gibson GA-5T that was parted out. It was a strange monster that had 2-EL84's for output instead of 2-6V6's... I'm just trying to get a decent sounding first amp under my belt. =)
Thanks,
Andy
Thanks,
Andy
0 x
-
- Occasional poster
- Posts: 141
- Joined: Thu 08/28/03 2:00 am
- Location: 5min South East of St. Louis, MO
- Contact:
-
- Newbie
- Posts: 58
- Joined: Thu 04/17/03 2:00 am
I don''t know what the difference would be in a stock 18 - ours has a plexi-type preamp (shared cathode, TMB + presence) coupled to a pretty standard 18w power section. Took awhile to tame tame the front-end gain and until we did that, the whole amp sounded harsh. Though I haven't heard one, I don't see how the "November" circuit can sound good without tweaking but again, I haven't heard one.
It also took awhile to get "rid of" the tube rectifier (didn't want to be chasing tubes) and the choke (another remnant of the plexi circuit). I'm not the one that made the circuit changes, but I kept complaining until I heard what I wanted ("uuns" on this board did the circuit work). Anyway, I'd never go back to a tube rectifier in this amp at this point. I'll see if I can get other's to pip in (uuns, sgtoverdrive?).
It also took awhile to get "rid of" the tube rectifier (didn't want to be chasing tubes) and the choke (another remnant of the plexi circuit). I'm not the one that made the circuit changes, but I kept complaining until I heard what I wanted ("uuns" on this board did the circuit work). Anyway, I'd never go back to a tube rectifier in this amp at this point. I'll see if I can get other's to pip in (uuns, sgtoverdrive?).
0 x
- s2
- Senior Amp Tech
- Posts: 3182
- Joined: Thu 05/20/04 2:00 am
- Location: Dallas, TX
- Contact:
I just used this little rectifier from Mouser for the first time: 821-SBT607. It is ecapsulated and has solder tabs, so you just screw it to the chassis and wire it up. Works great and rids you of the hassle of making your own. I think it cost something like $1.75 and is rated 1000V at 6A.
Here is a pic of it in action:
http://www.18watt.com/modules.php?set_a ... _photo.php
Here is a pic of it in action:
http://www.18watt.com/modules.php?set_a ... _photo.php
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
However, if you use FRED rectifiers (eg UF4007s), in theory at least, you can get a smoother sounding high end, due to less high frequency switching noise from the SS rectifiers getting in.JonFrum wrote:All things being equal, the rectifier shouldn't have anything to do with harshness. SS rectification should give you a tighter feel, quicker response.
0 x
Nature abhors a clean tube amp