314V PT no center tap... building a 18w ... drop B+ How?
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
- Chubsman
- Frequent poster
- Posts: 974
- Joined: Fri 11/25/05 2:00 am
- Location: Ottawa, ON - Canada
314V PT no center tap... building a 18w ... drop B+ How?
I have a PacTran PT that has no CT on the HV...which I measure 314VAC from lead to lead. This thing has no 5V tap either, so has to be SS recto...
314 X 1.4 = 440DCV unloaded.
I want to drop the B+... zener or droping 10W resistor?
314 X 1.4 = 440DCV unloaded.
I want to drop the B+... zener or droping 10W resistor?
Last edited by Chubsman on Wed 03/25/09 7:56 am, edited 1 time in total.
0 x
-
- Transformer Guy
- Posts: 1082
- Joined: Sun 03/12/06 2:00 am
- Location: Dalmatia
- Contact:
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Simple. Just stick one or more zener diodes in series with the B+ line, more or less anywhere between the first filter cap and the OT connection, with the stripe end(s) pointing back towards the rectifier. Check that the power dissipated by each zener (zener voltage X max current) is under half of what the zener power rating is. For large voltage drops you can add zeners in series, and their zener voltages add together, so you get a voltage drop approximately equal to the sum of their voltages. This also helps divide up the power dissipation between the zeners. Make sure the zeners are mounted with free air around them, so they don't overheat.
0 x
Nature abhors a clean tube amp
- Chubsman
- Frequent poster
- Posts: 974
- Joined: Fri 11/25/05 2:00 am
- Location: Ottawa, ON - Canada
Would I be better building this with 6v6 tubes?
Reason I say this is:
They often run in amps with B+ in excess of 400V with no difficulty. If the PT sags more you are of course safe, but if it is above 400V, no worries for 6V6s. They'll draw similar current from the HT as EL-84s would too, so safe there also. In the heater department they draw less current than EL-84s, .45 amps vs .76 amps, so no worries there either.
What does an 18watt sound like with 6v6?
Reason I say this is:
They often run in amps with B+ in excess of 400V with no difficulty. If the PT sags more you are of course safe, but if it is above 400V, no worries for 6V6s. They'll draw similar current from the HT as EL-84s would too, so safe there also. In the heater department they draw less current than EL-84s, .45 amps vs .76 amps, so no worries there either.
What does an 18watt sound like with 6v6?
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
It depends on how many volts you're dropping in the zener(s) multiplied by the maximum B+ current. Them make sure the zener is rated for at least double that figure. So for example, I recently installed an 18V zener in an amp with a pair of 6V6s, idling at 20mA, to get the voltage on the 6V6s down to around 440V. At peak the 6V6s will be taking about 30mA each max. Then allowing a further 10mA draw for the PI and preamp in the case of this amp, the power dissipation in the zener is 18V X 70mA = 1.26W, which is comfortable below 2.5W for a 5W zener.
If you use 6V6s, it may still be a good idea to use a larger resistor in the rail to drop the preamp voltages down to what they would be in a regular 18W.
If you use 6V6s, it may still be a good idea to use a larger resistor in the rail to drop the preamp voltages down to what they would be in a regular 18W.
0 x
Nature abhors a clean tube amp
- Chubsman
- Frequent poster
- Posts: 974
- Joined: Fri 11/25/05 2:00 am
- Location: Ottawa, ON - Canada
Ya I decided to just go with 2XEl84 and drop the voltage to 330V
This is a no CT 314V PT... so I am guessing I need to drop around 100V !...
I am trying to figure out what my options are... it's a 20W lead/Bass (2-12ax7 and 2-el84)
Wondering if 100V is too much... perhaps a combination of zener and large resistor...
Any advice would be appreciated...
Here is what I have:
NO CT PT with 314v lead-lead (No 5V tap... so no tube recto)
20W lead and bass kit
5W zeners
10W ceramic resistors...
What would you do... in order to not smoke this baby...
thanks
chubs
This is a no CT 314V PT... so I am guessing I need to drop around 100V !...
I am trying to figure out what my options are... it's a 20W lead/Bass (2-12ax7 and 2-el84)
Wondering if 100V is too much... perhaps a combination of zener and large resistor...
Any advice would be appreciated...
Here is what I have:
NO CT PT with 314v lead-lead (No 5V tap... so no tube recto)
20W lead and bass kit
5W zeners
10W ceramic resistors...
What would you do... in order to not smoke this baby...
thanks
chubs
0 x
-
- Verbose poster
- Posts: 1090
- Joined: Sun 12/12/04 2:00 am
- Location: City of Brothery Love
Wouldn't installing the zeners between the first filter and the usually red OT lead just lower the voltage to the OT and then plates of the power tubes? What about lowering the rest of the amps voltage, would you in that case install the zeners between stand-by and first filter?zaphod_phil wrote:Simple. Just stick one or more zener diodes in series with the B+ line, more or less anywhere between the first filter cap and the OT connection, with the stripe end(s) pointing back towards the rectifier. Check that the power dissipated by each zener (zener voltage X max current) is under half of what the zener power rating is. For large voltage drops you can add zeners in series, and their zener voltages add together, so you get a voltage drop approximately equal to the sum of their voltages. This also helps divide up the power dissipation between the zeners. Make sure the zeners are mounted with free air around them, so they don't overheat.
I use to install zeners off the HV ctr tap but you suggested this is not a good idea?
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
Not in an 18W (as well as many other amps), since the screen grid, PI and preamp power rails are all fed from the B+ line between the first filter cap and the OT centre-tap connection, via suitable voltage-dropping resistors. So everything gets dropped by the zener voltage.ajkimba wrote:Wouldn't installing the zeners between the first filter and the usually red OT lead just lower the voltage to the OT and then plates of the power tubes?
Personally, I don't like it, but it's not like it's a total no no.ajkimba wrote:I use to install zeners off the HV ctr tap but you suggested this is not a good idea?
In which case you need to have the EL84s running at around 400V, not 330V, or you'll have an 18W not a 20W. Just make sure to use rugged EL84s, such as EL84Ms, 7189s or preferably 7189As. If your B+ voltage turns out to be much above 400V, you can drop the remaining volts using zeners. To limit the power dissipated in individual zeners, you can connect two or more in series - eg three 9V zeners will give you 27V drop. You don't want to use a resistor here, as the amp will get saggy, and Marshall 20W amps are all about punch.Chubsman wrote:Ya I decided to just go with 2XEl84 and drop the voltage to 330V. I am trying to figure out what my options are... it's a 20W lead/Bass (2-12ax7 and 2-el84)
0 x
Nature abhors a clean tube amp
- Chubsman
- Frequent poster
- Posts: 974
- Joined: Fri 11/25/05 2:00 am
- Location: Ottawa, ON - Canada
Thanks ZP...
To be honnest what is really confusing me is the fact that I do not have a CT on the PT....
So If I use a bridge recto... will I still calculate the B+ with 1.4 X AC the PT is giving out stand alone... in this case 314V X 1.4 = 440V B+ ?
So then I would use a couple of zeners at the start of the B+ to lower around 40V... Am I making sense?
To be honnest what is really confusing me is the fact that I do not have a CT on the PT....
So If I use a bridge recto... will I still calculate the B+ with 1.4 X AC the PT is giving out stand alone... in this case 314V X 1.4 = 440V B+ ?
So then I would use a couple of zeners at the start of the B+ to lower around 40V... Am I making sense?
0 x
- GibsonGM
- Occasional poster
- Posts: 268
- Joined: Wed 12/06/06 2:00 am
- Location: Farmington, Maine
-
- Occasional poster
- Posts: 400
- Joined: Fri 06/16/06 2:00 am
Yes. However, that's the UNLOADED B+ voltage level. When you plug in your tubes that voltage will drop depending on the current capacity of your PT even if you use ss diodes. It may even drop down to an acceptable level for you.So If I use a bridge recto... will I still calculate the B+ with 1.4 X AC the PT is giving out stand alone... in this case 314V X 1.4 = 440V B+ ?
YesIs this the proper way to apply the Zener mod?
0 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
It's correct.... well almost ..... except that your zener diodes are the wrong way round. They need to look like they're pointing back toward the rectifiers and filter cap. Zeners are meant to operate reverse-biased.GibsonGM wrote:Is this the proper way to apply the Zener mod? I need to drop say 20V from my B+, want to make sure i'm doing this the right way.
0 x
Nature abhors a clean tube amp
- GibsonGM
- Occasional poster
- Posts: 268
- Joined: Wed 12/06/06 2:00 am
- Location: Farmington, Maine
AAAHHH, This way, then...I thoughts so but wasn't sure.
Thanks!
***EDIT - correct diagram inserted per 57's comment below, cathodes towards standby (+) side ***
Thanks!
***EDIT - correct diagram inserted per 57's comment below, cathodes towards standby (+) side ***
Last edited by GibsonGM on Wed 04/01/09 9:10 pm, edited 2 times in total.
0 x