36W Turretboard Layout
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
36W Turretboard Layout
Before I heat up the Hakko, would greatly appreciate a second or third set of critical eyes on my board design for this 36W build. Is anything on this asinine? I haven't drawn up a schem or a complete layout yet, but it's adapted from the Ceriatone layout. Again, fantastic board prepared for me by Doug Hoffman, cost was $25 and arrived in 30 hours from when I submitted my DIYLC file into Doug's system.
Thanks in advance!
Thanks in advance!
You do not have the required permissions to view the files attached to this post.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 36W Turretboard Layout
Without diving deep into it, the thing that stands out the most is that the preamp filter caps are arbitrarily placed. Whenever possible, they should be directly next to a given stage's cathode cap. Making that adjustment will also make the turret layout easier/cleaner.
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
It looked funny to me at first also, this is basically the ceriatone board sequence. It's actually very similar to Richie's 36 Watt TMB Layout v.2.0 so I figured I'd give it a try.
0 x
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
I think you meant "coupling cap". That is exactly where they are.JMPGuitars wrote: ↑Mon 06/08/20 6:18 pmWhenever possible, they should be directly next to a given stage's cathode cap.
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 36W Turretboard Layout
No, I meant what I said. A stage's filter/decoupling cap should be next to its cathode cap.crgfrench wrote: ↑Wed 06/10/20 1:53 amI think you meant "coupling cap". That is exactly where they are.JMPGuitars wrote: ↑Mon 06/08/20 6:18 pmWhenever possible, they should be directly next to a given stage's cathode cap.
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
Why would that be? I would think it should be near the anode rather than the cathode -- from a schematic viewpoint?
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 36W Turretboard Layout
It's not a schematic thing. I don't remember the reasoning, but maybe when Zaphod_Phil is less busy with work he can explain it. I think he told me why a while ago, but I forget.
2 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
Picked up a 2x12 cabinet loaded with WGS green berets today for $200!
You do not have the required permissions to view the files attached to this post.
3 x
- zaphod_phil
- Builder, Admin
- Posts: 15208
- Joined: Wed 03/19/03 2:00 am
- Location: YYZ
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: 36W Turretboard Layout
Going back to the " hauling gear period"... that's gonna be a heavy piece of equipment
1 x
"THIS should be played at high volume..preferably in a residential area"
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
I'm installing this board into a 1x12 cab, with a Ceriatone 36W chassis and Heyboer iron from GDS. I posted these pics in another thread but they probably really belong here since this is where I'll post updates of this build. The GDS PT has a smaller footprint than the Ceriatone PT so I made this adapter.
The corners of the PT opening need to also be filed or drilled slightly for this, as you can see in the images.
The corners of the PT opening need to also be filed or drilled slightly for this, as you can see in the images.
You do not have the required permissions to view the files attached to this post.
3 x
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
Board soldered, all except the ground bus.
You do not have the required permissions to view the files attached to this post.
2 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: 36W Turretboard Layout
Looking nice Craig!!!
Watch out to not overheat the caps and resistors when you attach the ground buss. That takes more heat and time wit the soldering tip, so it's hard to not overheat other components.
I'm also educated connecting the components laterally on the turrets instead of in the top hole. That way there is a better mechanical connection in case solder would come loose.
1 x
"THIS should be played at high volume..preferably in a residential area"
- colossal
- Moderator
- Posts: 450
- Joined: Thu 05/10/07 2:00 am
- Location: Moving through Kashmir
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
Thanks guys. I always use a heat sink clip when soldering every cap lead. Takes a bit more time but I like the security.
0 x
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
I prefer mounting them in the top hole, it's the most solid connection. It also facilitates later mods or repairs down the road. Doug Hoffman recommends this method, see
https://el34world.com/boardmaker/BOARD3.htm
Also, if it's good enough for Danny Russell, it's good enough for me, see http://www.bletchleyamps.com/www.bletch ... oduct.html
OTOH, Mark Bartel wraps them your way and his amps are awesome too.
Bottom line, either method is fine if you solder properly.
1 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: 36W Turretboard Layout
You're rightcrgfrench wrote: ↑Sat 06/20/20 9:42 pmI prefer mounting them in the top hole, it's the most solid connection. It also facilitates later mods or repairs down the road. Doug Hoffman recommends this method, see
https://el34world.com/boardmaker/BOARD3.htm
Also, if it's good enough for Danny Russell, it's good enough for me, see http://www.bletchleyamps.com/www.bletch ... oduct.html
OTOH, Mark Bartel wraps them your way and his amps are awesome too.
Bottom line, either method is fine if you solder properly.
1 x
"THIS should be played at high volume..preferably in a residential area"
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 36W Turretboard Layout
Either method can be fine (if you're skilled), but the external j-hook is absolutely superior. Besides the fact that the j-hook gives you a solid mechanical connection that top mounting doesn't, not all turrets heat evenly throughout (inconsistent plating, etc..), so you can get potential cold/poor joints that you can't see. In other words, top mounting does NOT give the most solid connection, not even close.
For a well experienced technician with very good soldering skills, and 100% perfect turrets, it's maybe not a big deal. But for the average DIYer, it can be a huge difference, especially in the real world were turrets aren't always as consistent as we'd like.
Thanks,
Josh
For a well experienced technician with very good soldering skills, and 100% perfect turrets, it's maybe not a big deal. But for the average DIYer, it can be a huge difference, especially in the real world were turrets aren't always as consistent as we'd like.
Thanks,
Josh
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- JMPGuitars
- Super Duper Admin
- Posts: 3989
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 36W Turretboard Layout
Side note: neither methods facilitates modification better than the other if you don't have the right tools. I have a good desoldering gun, so it makes no difference to me.
If you're top mounting your components without an adequate desoldering gun, then it's possible you're not removing all the solder from the turret when making changes. A less-experienced DIYer will likely drip solder through the bottom of the turret (I've seen this - like a solder stalactite).
On the other hand, if you're externally mounting your components, you can more easily remove solder with the common tedious methods like desolding braid or spring pumps.
Obviously Craig's skills are higher than the typical DIYer, but since the two of you won't be the only people reading this thread, it's important to point these things out.
Thanks,
Josh
If you're top mounting your components without an adequate desoldering gun, then it's possible you're not removing all the solder from the turret when making changes. A less-experienced DIYer will likely drip solder through the bottom of the turret (I've seen this - like a solder stalactite).
On the other hand, if you're externally mounting your components, you can more easily remove solder with the common tedious methods like desolding braid or spring pumps.
Obviously Craig's skills are higher than the typical DIYer, but since the two of you won't be the only people reading this thread, it's important to point these things out.
Thanks,
Josh
1 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- crgfrench
- Frequent poster
- Posts: 827
- Joined: Fri 04/27/18 3:02 am
Re: 36W Turretboard Layout
Speaking of J hook method, I have 3 under-board solid wires on this build (the last B+ run and a couple others); I run them up all the way through and j hook them over the top. I was fortunate to have been a professional TIG welder when I was younger which helps with soldering generally, and the non-eutectic nature of 60/40 in particular.
0 x