Faceplate / badge / logo / name-plate
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
-
- Unrated
- Posts: 4
- Joined: Fri 03/28/14 9:22 am
Faceplate / badge / logo / name-plate
Greetings... I built an 18watt from scratch, but purchased a cabinet from Mojotone and I have to say, it looks great, but it's missing something: a faceplate / logo / badge / name-plate.
I will put my surname there, a not-so-subtle nod to Marshall. What size are the Marshall logos on the original (and reissue ) amps?? That is, if you were to fit the logo into a rectangle (width, height).
I plan to have a local trophy shop make a plate for me and can't decide on the size of plate to use...
Thanks in advance,
--Jesse
I will put my surname there, a not-so-subtle nod to Marshall. What size are the Marshall logos on the original (and reissue ) amps?? That is, if you were to fit the logo into a rectangle (width, height).
I plan to have a local trophy shop make a plate for me and can't decide on the size of plate to use...
Thanks in advance,
--Jesse
0 x
-
- Superior Amp Tech
- Posts: 753
- Joined: Fri 01/08/10 2:00 am
- Location: Scotland
Re: Faceplate / badge / logo / name-plate
There are some drawings of faceplates in the downloads section here. You may find enough information to get started sizing your plate.
Dd
Dd
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Faceplate / badge / logo / name-plate
I have a guy that does my 3D printed logos and lasercut/engravement of faceplates. But I'm from Belgium
Easy enough to find people like that. Just respond to advertisements of people that sell 3D printers 2nd handYou do not have the required permissions to view the files attached to this post.
2 x
"THIS should be played at high volume..preferably in a residential area"
-
- Unrated
- Posts: 4
- Joined: Fri 03/28/14 9:22 am
Re: Faceplate / badge / logo / name-plate
Thanks, Davie Dawg... I did a search, but that eluded me. Much obliged.
--Jesse
--Jesse
Last edited by jessetrbo on Sat 07/17/21 8:03 pm, edited 1 time in total.
0 x
-
- Unrated
- Posts: 4
- Joined: Fri 03/28/14 9:22 am
-
- Unrated
- Posts: 4
- Joined: Fri 03/28/14 9:22 am
Re: Faceplate / badge / logo / name-plate
Davie Dawg, I think that '"faceplate" is not what I'm looking for... The Downloads section seems to cover everything else, but what I'm after.
I need the basic dimensions of the 'Marshall' logo that would be attached to the front of the amp. I'll use a slightly different aesthetic (rectangular engraved name plate), but I'd like to keep the physical proportions similar to the original amps.
Could anybody make a quick height x width measurement of the nameplate or logo that you used on your 18watt?? Better yet, if you have an original, could you measure?
--Jesse
I need the basic dimensions of the 'Marshall' logo that would be attached to the front of the amp. I'll use a slightly different aesthetic (rectangular engraved name plate), but I'd like to keep the physical proportions similar to the original amps.
Could anybody make a quick height x width measurement of the nameplate or logo that you used on your 18watt?? Better yet, if you have an original, could you measure?
--Jesse
0 x
- Bieworm
- Verbose Moderator
- Posts: 2314
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: Faceplate / badge / logo / name-plate
Thanx. The guy I built it for is raving about it. Every week I receive a message from him of how exciting it is to play it.
It's a 1 watt JTM145 kinda clone
3 x
"THIS should be played at high volume..preferably in a residential area"