1974x PT replacement
Moderators: zaphod_phil, Daviedawg, Graydon, CurtissRobin, colossal
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
I've got a Craftsman MM. 82024. This one does not get capacitance. Resistor does measure 200 ohms. I'm not sure what to do just now. I don't want it running cold. Rather hot. I don't care if it burns up tubes......should I order a 150R bias resistor? 160R? Change them out, see what sounds best? what's the best step by step to dial this thing in?
It does not have a bleed resistor, I do it manually. I triple check before sticking my fingers in there. Everytime, just FYI
It does not have a bleed resistor, I do it manually. I triple check before sticking my fingers in there. Everytime, just FYI
0 x
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
PS....I'd prefer not burning up tubes. LOL. Just to clarify, but I'd prefer that than running too cold
0 x
- JMPGuitars
- Super Duper Admin
- Posts: 3968
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 1974x PT replacement
The ONLY correct thing to do is to measure your tube dissipation. You want the power tubes running between 75 to 85%. That's the sweet spot for tone and reliability.
You can use a calculator: https://robrobinette.com/Tube_Bias_Calculator.htm
Thanks,
Josh
You can use a calculator: https://robrobinette.com/Tube_Bias_Calculator.htm
Thanks,
Josh
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
Thx... Picked up a Fluke MM. I needed to replace this craftsman for a while now. I've used this link before. I'll go through everything this eve.....Plugged in a bit ago and it does not sound as good as I'm certain it can.. Like I said, I'll go thru it tonight....Thx for the link JMP
0 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: 1974x PT replacement
Monitor the bias voltage of the el84’s for a good 10 mins it should be stable after the tubes have warmed up.you need to be certain there was’nt an issue that caused the PT failure.Tubes can leak internally.
0 x
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
I've got 323v Plate to Cathode voltage, using the link and directions JMP sent, but I'm not sure where to go from here. I realize that this is all new to me, it's not like the bigger amps. Not that I knew a lot about them either, but I'd biased more than a few. Always with a trim pot and a MM, but with these el84's and a cathode bias, it's back to square 1. I appreciate the guidance.........where do I go from here to determine if I'm running cold and then what to do about it.
0 x
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
this voltage stayed steady, in both tubes, for well over 10 min...323.5 in one el84 and 321.5 in the other
0 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: 1974x PT replacement
That is your plate voltage,bias cathode voltage is measured from pin3 of the el84’s socket to ground “chassis” what does that read and is it stable after the tubes have warmed up?
Last edited by geoff 1965 on Wed 10/20/21 8:26 am, edited 1 time in total.
0 x
- Bieworm
- Verbose Moderator
- Posts: 2305
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: 1974x PT replacement
To use the robrob calculator Josh linked you...
1. Select tube
2. Fill in A to K voltage ( voltage pin 7 minus voltage pin 3)
3. Press calculate
4. Type 2 where it says number of tubes that share cathode resistor
5. Enter resistor value
6. Enter cathode voltage ( voltage of pin 3)
7. Press calculate
Now you have the result. Make sure you look at the cathode biased percentage
1. Select tube
2. Fill in A to K voltage ( voltage pin 7 minus voltage pin 3)
3. Press calculate
4. Type 2 where it says number of tubes that share cathode resistor
5. Enter resistor value
6. Enter cathode voltage ( voltage of pin 3)
7. Press calculate
Now you have the result. Make sure you look at the cathode biased percentage
1 x
"THIS should be played at high volume..preferably in a residential area"
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
cathode voltage started at 12.5. After 10 min it was 12.8....then @ 15 min it was 12.68........IDK if that significant flux of not.
0 x
- Bieworm
- Verbose Moderator
- Posts: 2305
- Joined: Mon 02/10/20 8:24 am
- Location: Belgium
Re: 1974x PT replacement
Wrong tube choice. It should be EL84 or 6bq5 . What tube did you select?
According to your voltages you've got 82.5% .. so that's near perfect!
0 x
"THIS should be played at high volume..preferably in a residential area"
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
I deleted that pic because I was going to run the numbers again. I had the plate to cathode number wrong. should have been 323.5, not 330.....and if I need to use the el84 12w, then it'll be diff again. Give me a few and I'll do it again
0 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: 1974x PT replacement
cathode voltage looks okay,that was my concern especially with the PT failure but if it dropped to 12.6 from 12.8 after 15 mins that's pretty stable.
0 x
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
This is it. Checked and rechecked. Let it heat up for 15 min fully powered. No significant change from 1st to last readings
You do not have the required permissions to view the files attached to this post.
1 x
- JMPGuitars
- Super Duper Admin
- Posts: 3968
- Joined: Tue 09/18/12 8:00 pm
- Location: South Central, MA
- Contact:
Re: 1974x PT replacement
80% is excellent, assuming all the values are correct. I wouldn't change it. Don't arbitrarily change stuff without good reason.
Thanks,
Josh
Thanks,
Josh
0 x
'I installed a skylight in my apartment yesterday... The people who live above me are furious.' - Steven Wright
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
Modern Ground Schemes
Soldering Technique
B+ Voltage Reduction
Amplifier Tools & Parts Info
Web Design: DolceVittoria.com
Guitars / Amps / Effects: JMPGuitars.com
(anti)Social: Facebook · Instagram
Items for Sale
- foreverstrung
- Occasional poster
- Posts: 241
- Joined: Sun 10/10/21 5:53 pm
- Location: Seabrook Texas
- Contact:
Re: 1974x PT replacement
Ya, I'm not going to change anything. Numbers are correct. I triple checked. Put the amp back together 100% and put it thru the motions for about an hour. Sounds fantastic. appreciate all the help
3 x
-
- Verbose poster
- Posts: 1118
- Joined: Mon 01/04/16 3:52 pm
Re: 1974x PT replacement
Well done! glad you are happy with it,I was surprised at the quite low 318 plate voltage and it looks like Marshall aimed at breakup with this design,the stock 91R bias resistor would drop the plate & cathode voltage even more!
1 x
-
- Unrated
- Posts: 5
- Joined: Mon 08/01/22 11:27 am
Re: 1974x PT replacement
Foreverstrung!! Thanks for the idea to contact Marshall about the bad transformer. Mine went out on my 2005 1974x and I contacted them and they are sending me a new on which should be here in a couple of days!!
Glad you got yours going again!!
Glad you got yours going again!!
1 x